|
1.
|
|
|
Keyboard Repeat
|
|
|
i18n: file: kcmmiscwidget.ui:59
i18n: ectx: property (title), widget (QGroupBox, keyboardRepeatGroupBox)
|
|
|
|
Opakovanie klávesov
|
|
Translated by
Miroslav David
|
|
|
|
Located in
rc.cpp:147
|
|
2.
|
|
|
If you check this option, pressing and holding down a key emits the same character over and over again. For example, pressing and holding down the Tab key will have the same effect as that of pressing that key several times in succession: Tab characters continue to be emitted until you release the key.
|
|
|
i18n: file: kcmmiscwidget.ui:59
i18n: ectx: property (whatsThis), widget (QCheckBox, repeatBox)
|
|
|
|
Ak začiarknete túto voľbu, stlačenie a držanie klávesu vygeneruje opakovane ten istý znak. Napríklad, stlačenie a držanie klávesu Tab bude mať ten istý efekt ako jeho opakované stlačenie: znaky tabelátora budú generované až kým neuvoľníte kláves.
|
|
Translated by
Michal Sulek
|
|
|
|
Located in
rc.cpp:136 rc.cpp:308
|
|
3.
|
|
|
&Enable keyboard repeat
|
|
|
i18n: file: kcmmiscwidget.ui:62
i18n: ectx: property (text), widget (QCheckBox, repeatBox)
|
|
|
|
&Povoliť opakovanie klávesov
|
|
Translated by
Michal Sulek
|
|
|
|
Located in
rc.cpp:139 rc.cpp:311
|
|
4.
|
|
|
&Delay:
|
|
|
i18n: file: kcmmiscwidget.ui:123
i18n: ectx: property (text), widget (QLabel, lblDelay)
|
|
|
|
O&neskorenie:
|
|
Translated by
Miroslav David
|
|
|
|
Located in
rc.cpp:159
|
|
5.
|
|
|
If supported, this option allows you to set the delay after which a pressed key will start generating keycodes. The 'Repeat rate' option controls the frequency of these keycodes.
|
|
|
i18n: file: kcmmiscwidget.ui:133
i18n: ectx: property (whatsThis), widget (QSlider, delaySlider)
i18n: file: kcmmiscwidget.ui:161
i18n: ectx: property (whatsThis), widget (KIntNumInput, delay)
|
|
|
|
Ak je podporovaná, táto voľba vám umožní nastaviť dĺžku oneskorenia, po ktorom stlačený kláves začne generovať znaky. Voľba 'Rýchlosť' určuje frekvenciu týchto kódov.
|
|
Translated by
Michal Sulek
|
|
|
|
Located in
rc.cpp:162 rc.cpp:165
|
|
6.
|
|
|
&Rate:
|
|
|
i18n: file: kcmmiscwidget.ui:177
i18n: ectx: property (text), widget (QLabel, lblRate)
|
|
|
|
&Rýchlosť:
|
|
Translated by
Miroslav David
|
|
|
|
Located in
rc.cpp:171
|
|
7.
|
|
|
If supported, this option allows you to set the rate at which keycodes are generated while a key is pressed.
|
|
|
i18n: file: kcmmiscwidget.ui:187
i18n: ectx: property (whatsThis), widget (QSlider, rateSlider)
i18n: file: kcmmiscwidget.ui:215
i18n: ectx: property (whatsThis), widget (KDoubleNumInput, rate)
|
|
|
|
Ak je podporovaná, táto voľba vám umožní nastaviť rýchlosť, s akou sa nové znaky generujú zatiaľ čo je kláves stlačený.
|
|
Translated by
Michal Sulek
|
|
|
|
Located in
rc.cpp:174 rc.cpp:177
|
|
8.
|
|
|
If supported, this option allows you to setup the state of NumLock after KDE startup.<p>You can configure NumLock to be turned on or off, or configure KDE not to set NumLock state.
|
|
|
i18n: file: kcmmiscwidget.ui:17
i18n: ectx: property (whatsThis), widget (KButtonGroup, numlockGroupBox)
|
|
|
|
Ak je podporovaná, táto voľba vám umožní nastaviť stav NumLock po spustení KDE.<p>Môžete nastaviť, aby bol NumLock zapnutý, vypnutý, alebo aby KDE nenastavovalo stav NumLock.
|
|
Translated by
Michal Sulek
|
|
|
|
Located in
rc.cpp:132
|
|
9.
|
|
|
NumLock on KDE Startup
|
|
|
i18n: file: kcmmiscwidget.ui:20
i18n: ectx: property (title), widget (KButtonGroup, numlockGroupBox)
|
|
|
|
NumLock pri štarte KDE
|
|
Translated by
Miroslav David
|
|
|
|
Located in
rc.cpp:135
|
|
10.
|
|
|
T&urn on
|
|
|
i18n: file: kcmmiscwidget.ui:32
i18n: ectx: property (text), widget (QRadioButton, RadioButton1)
i18n: file: kcmmiscwidget.ui:71
i18n: ectx: property (text), widget (QRadioButton, keyboardRepeatOnRadioButton)
|
|
|
|
&Zapnúť
|
|
Translated by
Miroslav David
|
|
|
|
Located in
rc.cpp:138 rc.cpp:150
|