|
|
1.
|
|
|
Keyboard Repeat
|
|
|
i18n: file: kcmmiscwidget.ui:59
i18n: ectx: property (title), widget (QGroupBox, keyboardRepeatGroupBox)
|
|
|
|
|
Opakování klávesy
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:147
|
|
|
2.
|
|
|
If you check this option, pressing and holding down a key emits the same character over and over again. For example, pressing and holding down the Tab key will have the same effect as that of pressing that key several times in succession: Tab characters continue to be emitted until you release the key.
|
|
|
i18n: file: kcmmiscwidget.ui:59
i18n: ectx: property (whatsThis), widget (QCheckBox, repeatBox)
|
|
|
|
|
Zaškrtnete-li tuto volbu, pak po stlačení a podržení klávesy se bude generovat neustále ten samý znak. Například stisknutí a podržení klávesy TAB bude mít stejný účinek jako opakované stisknutí této klávesy. Daný znak bude generován tak dlouho, dokud bude stisknuta příslušná klávesa.
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:136 rc.cpp:308
|
|
|
3.
|
|
|
&Enable keyboard repeat
|
|
|
i18n: file: kcmmiscwidget.ui:62
i18n: ectx: property (text), widget (QCheckBox, repeatBox)
|
|
|
|
|
Povolit opakování kláv&es
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:139 rc.cpp:311
|
|
|
4.
|
|
|
&Delay:
|
|
|
i18n: file: kcmmiscwidget.ui:123
i18n: ectx: property (text), widget (QLabel, lblDelay)
|
|
|
|
|
Pro&dleva:
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:159
|
|
|
5.
|
|
|
If supported, this option allows you to set the delay after which a pressed key will start generating keycodes. The 'Repeat rate' option controls the frequency of these keycodes.
|
|
|
i18n: file: kcmmiscwidget.ui:133
i18n: ectx: property (whatsThis), widget (QSlider, delaySlider)
i18n: file: kcmmiscwidget.ui:161
i18n: ectx: property (whatsThis), widget (KIntNumInput, delay)
|
|
|
|
|
Pokud je podporováno, umožní vám nastavit prodlevu, po které začne stisknutá klávesa generovat kódy. 'Rychlost' určuje frekvenci těchto kódů.
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:162 rc.cpp:165
|
|
|
6.
|
|
|
&Rate:
|
|
|
i18n: file: kcmmiscwidget.ui:177
i18n: ectx: property (text), widget (QLabel, lblRate)
|
|
|
|
|
&Rychlost:
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:171
|
|
|
7.
|
|
|
If supported, this option allows you to set the rate at which keycodes are generated while a key is pressed.
|
|
|
i18n: file: kcmmiscwidget.ui:187
i18n: ectx: property (whatsThis), widget (QSlider, rateSlider)
i18n: file: kcmmiscwidget.ui:215
i18n: ectx: property (whatsThis), widget (KDoubleNumInput, rate)
|
|
|
|
|
Pokud je podporováno, umožní vám nastavit rychlost, kterou jsou generovány kódy při stisku klávesy.
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:174 rc.cpp:177
|
|
|
8.
|
|
|
If supported, this option allows you to setup the state of NumLock after KDE startup.<p>You can configure NumLock to be turned on or off, or configure KDE not to set NumLock state.
|
|
|
i18n: file: kcmmiscwidget.ui:17
i18n: ectx: property (whatsThis), widget (KButtonGroup, numlockGroupBox)
|
|
|
|
|
Je-li tato volba podporována, tak umožní nastavení stavu numerické klávesnice po startu KDE.<p> Můžete nastavit zapnutí nebo vypnutí numerické klávesnice, nebo můžete zvolit, aby se numerická klávesnice nenastavovala prostřednictvím KDE.
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:132
|
|
|
9.
|
|
|
NumLock on KDE Startup
|
|
|
i18n: file: kcmmiscwidget.ui:20
i18n: ectx: property (title), widget (KButtonGroup, numlockGroupBox)
|
|
|
|
|
NumLock při spuštění KDE
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:135
|
|
|
10.
|
|
|
T&urn on
|
|
|
i18n: file: kcmmiscwidget.ui:32
i18n: ectx: property (text), widget (QRadioButton, RadioButton1)
i18n: file: kcmmiscwidget.ui:71
i18n: ectx: property (text), widget (QRadioButton, keyboardRepeatOnRadioButton)
|
|
|
|
|
Zapno&ut
|
|
Translated by
Lukáš Tinkl
|
|
|
|
Located in
rc.cpp:138 rc.cpp:150
|
