|
|
330.
|
|
|
Note that correct <b>incoming connection settings are needed for searches and file downloads</b> to work. These settings <b>have no effect on ability to connecting to hubs or downloading hublists</b>. This FAQ assumes that <u>you are able to download hublists and connect to hubs</u> as well as other peers can upload files from you. If this is not true then you must elminate another kind of problems before go on with this FAQ:
|
|
|
type: Content of: <html><body><p>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:28
|
|
|
340.
|
|
|
To manually configure your connectivity settings, uncheck <a po4a-id=0> Let DC++ determine the best connectivity settings</a> in the Connectivity settings pane of the settings dialog. This will enable the controls on the <a po4a-id=1>Manual configuration</a> pane where you can alter connectivity settings manually.
|
|
|
type: Content of: <html><body><p>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:76
|
|
|
349.
|
|
|
Click OK. This will close the Settings window.
|
|
|
type: Content of: <html><body><p><ul><li>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:111 help/faq_connection.html:160
|
|
|
350.
|
|
|
Test active mode by joining several hubs and doing a search for a common term. You should get results back. If not, then you are likely behind a router, have an internal IP address or haven't properly configured your <a po4a-id=0>security software to unblock DC++</a>.
|
|
|
type: Content of: <html><body><ul><li>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:114
|
|
|
352.
|
|
|
Setting up active mode if you are behind a router
|
|
|
type: Content of: <html><body><h2>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:120
|
|
|
354.
|
|
|
Automatic port mapping configuration
|
|
|
type: Content of: <html><body><h3>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:131
|
|
|
361.
|
|
|
Make absolutely sure you have properly configured your <a po4a-id=0>security software to unblock DC++</a>
|
|
|
type: Content of: <html><body><p><ul><li>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:172
|
|
|
364.
|
|
|
Manual port mapping configuration
|
|
|
type: Content of: <html><body><h3>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:192
|
|
|
366.
|
|
|
Select passive mode as the last resort
|
|
|
type: Content of: <html><body><h3>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_connection.html:198
|
|
|
389.
|
|
|
Use the uninstaller that followed when you used the installer. It will remove all installed program files and (if you choose so) will delete all of your settings and unfinished downloads as well.
|
|
|
type: Content of: <html><body><p>
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
help/faq_install.html:22
|
